PART 1 - GENERAL
A. Section Includes: Furnishing of all labor, materials, services and equipment necessary for the supply and installation of antimicrobial crystalline additive to concrete as indicated on the drawings and as specified herein.
B. Related Sections:
1. Section 031000 - Concrete Forming
2. Section 032000 - Concrete Reinforcement
3. Section 031516 - Concrete Construction Joints
4. Section 033713 - Shotcrete
5. Section 034000 - Precast Concrete
6. Section 071616 - Crystalline Coatings
7. Section 079000 - Joint Protection
A. Applicable Standards: The following standards are referenced herein.
1. American Society for Testing and Materials (ASTM)
2. Army Corps of Engineers (CRD)
3. American Concrete Institute (ACI)
4. International Organization for Standardization (ISO)
5. European Standards (EN)
1.03 System Description
A. Antimicrobial Crystalline Waterproofing Additive: Concrete protection and waterproofing system shall be of the antimicrobial crystalline type that chemically controls and permanently fixes both a non-soluble crystalline structure within the pores and capillary tracts of the concrete as well as bio-active mineral solids into the concrete matrix. This dual system additive causes the concrete to become sealed against the penetration of liquids from any direction and protects the concrete from deterioration due to harsh environmental conditions. The product shall be of powder form and introduced to the mix during concrete production. The product shall be an EPA registered integral concrete admixture for the prevention of microbial induced corrosion (MIC) typically found in concrete tanks, pipes, manholes, and other structures/elements in sewage and drainage systems.
1.04 System Performance Requirements
A. Testing Requirements: Antimicrobial crystalline waterproofing system shall have been tested in accordance with the following standards and conditions and as per the manufacturer’s dosage range, and the testing results shall meet or exceed the performance requirements as specified herein.
B. Independent Laboratory: Testing shall have been performed by an accredited independent laboratory meeting the requirements of ASTM E 329 or other applicable international standard for certification of testing laboratories.
C. Indicator: The Admixture shall include an indicator that visually identifies concrete that includes Xypex Bio-San C500.
D. Antimicrobial Effect:Independent testing shall be performed according to ISO 22196 (Mod.) "Measurement of Antibacterial Activity on Plastics and other Non-Porous Surfaces”. Treated and non-treated control concrete samples shall be tested and a definite anti-microbial effect shall be evidenced by a significant reduction in formation of Thiobacillus Novellus / Starkeya Novella bacteria on the treated samples versus the non-treated samples.
E. Concrete Corrosion Rate: Treated and non-treated control concrete samples shall be tested in a live wastewater environment with high concentrations of H2S. Treated samples shall show at least 9 times less mass loss after 10 years as compared to control samples.
F. Long-term Antimicrobial Action and Efficacy:The antimicrobial admixture must show long-term antimicrobial action and efficacy as demonstrated by minimal bacterial concentration on the treated concrete after 10 years exposure to an elevated H2S live wastewater environment.
G. Crystalline Formation: Crystallizing capability of waterproofing system shall be evidenced by independent SEM (Scanning Electron Microscope) photographs showing crystalline formations within the concrete matrix.
H. Permeability 1: Independent testing shall be performed according to a U.S. Army Corps of Engineers CRD-C48 (Mod.) "Permeability of Concrete". Concrete samples shall be pressure tested to 150 psi (350 foot head of water) or 1.05 MPa (106 m head of water). After 5 days the untreated samples shall leak and the treated samples shall exhibit no measurable leakage.
I. Permeability 2: Independent testing shall be performed according to EN 12390-8. Treated samples shall be exposed to water with a pressure of 0.5 MPa for 72 hours. Treated samples must exhibit a reduction in permeability coefficient of at least 80% when compared to control concrete. Control samples must have a depth of penetration of at least 50 mm.
J. Sulfuric Acid Resistance: Independent testing shall be performed to determine "Sulfuric Acid Resistance of Concrete Specimens". Treated concrete samples dosed at 3% shall be tested against untreated control samples. All samples shall be immersed in 7% sulfuric acid and weighed daily until a control sample reaches a mass loss of 50%. On final weighing the percentage mass loss of the treated samples shall be significantly lower than the control samples.
K. Sulfate Resistance: Independent testing shall be performed to determine "Sulfate Resistance of Concrete Specimens" treated with integral crystalline admixture. Treated and untreated samples shall be immersed in a concentrated sulfate solution for at least 4 months. On final weighing the percentage mass loss of the treated samples shall be significantly lower than the control samples.
L. Compressive Strength: Concrete samples containing the antimicrobial crystalline waterproofing additive shall be tested against an untreated control sample of the same mix. At 28 days, the treated samples shall exhibit equal or increased compressive strength over the control sample.
A. General: Submit listed submittals in accordance with conditions of the Contract and with Division 1 Submittal Procedures Section.
B. Product Data: Submit product data, including manufacturer's specifications, installation instructions, and general recommendations for concrete protection and waterproofing applications.
C. Test Reports: Submit, for acceptance, complete test reports from approved independent testing facilities certifying that antimicrobial crystalline waterproofing system conforms to performance characteristics and testing requirements specified herein.
D. Manufacturer’s Certification: Provide document signed by manufacturer or manufacturer's representative certifying that the materials to be installed comply with the requirements of this specification.
1.06 Quality Assurance
A. Manufacturer Qualifications: Manufacturer to be ISO 9001 registered, and to have no less than 10 years experience in manufacturing crystalline waterproofing additives. Manufacturer must be capable of providing field service representation during construction phase. Manufacturers who cannot provide ongoing field support or who cannot provide the performance test data specified herein will not be considered for the project.
B. Installer: Ready-mix supplier and/or installer of antimicrobial crystalline waterproofing additive shall be approved by the manufacturer or manufacturer's representative in writing.
C. Pre-Installation Conference: Prior to installation of antimicrobial waterproofing system, conduct meeting with Architect/Engineer, owner's representative, concrete supplier, concrete placer and antimicrobial waterproofing manufacturer's representative to verify and review the following:
1. Project requirements for antimicrobial protection and waterproofing as set out in Contract Documents.
2. Manufacturer's product data including mixing and installation instructions.
D. Technical Consultation: The manufacturer's representative shall provide technical consultation on antimicrobial protection and waterproofing applications and shall provide on-site support as needed.
1.07 Delivery, Storage and Handling
A. Ordering: Comply with manufacturer's ordering instructions and lead time requirements to avoid construction delays.
B. Delivery: Deliver packaged waterproofing materials to project site in original undamaged containers, with manufacturer's labels and seals intact.
C. Storage: Store waterproofing materials in dry, enclosed location, at a minimum temperature of 45°F (7°C).
A. Project Warranty: Refer to conditions of the Contract for project warranty provisions.
B. Manufacturer’s Warranty: Manufacturer shall provide standard product warranty executed by authorized company official.
Part 1 - General | Part 2 - Products
| Part 3 - Execution